WATER LEAK TEST MACHINE FOR ALUMINUM WHEELS 

(MADE IN THE USA)

Rotary Leak Test Machine. Machine capabilities are a 24" wheel diameter with a 14" width.  Clamp plates are rubber-coated to assure an air tight fit seal with wheel and are spaced a minimum 14" apart. The 28” diameter upper platen is flat to accommodate most wheel styles and is interchangeable with a minimum of down time. Operator loads wheel onto clamp assembly.

WATER LEAK TEST MACHINE FOR ALUMINUM WHEELS 

(MADE IN THE USA)

Rotary Leak Test Machine. Machine capabilities are a 24" wheel diameter with a 14" width.  Clamp plates are rubber-coated to assure an air tight fit seal with wheel and are spaced a minimum 14" apart. The 28” diameter upper platen is flat to accommodate most wheel styles and is interchangeable with a minimum of down time. Operator loads wheel onto clamp assembly.

WATER LEAK TEST MACHINE FOR ALUMINUM WHEELS 

(MADE IN THE USA)

Rotary Leak Test Machine

Machine capabilities are a 24" wheel diameter with a 14" width.  Clamp plates are rubber-coated to assure an air tight fit seal with wheel and are spaced a minimum 14" apart. The 28” diameter upper platen is flat to accommodate most wheel styles and is interchangeable with a minimum of down time. Operator loads wheel onto clamp assembly.

Machine Details

  • Machine is equipped with two-hand anti-tie down controls, for operator safety.
  • Water tank is stainless steel with ½” polycarbonate plastic window for visual inspection.
  • Water tank will be equipped with two (2) 1.5” NPT connection fittings.
  • Urethane is 90 durometer on platens. 
  • Cycle time is estimated at 35-45 seconds. {PLC is AB}
  • No Hydraulic Power Pack Required. Power requirement is 110 Volt. 
  • Air requirement 75psi with ½” air supply line to machine
  • Machine Dimensions are: 50” Wide x 170” Tall x 57” Deep. Machine weight is 3,600 Lbs.
  • Made in the USA
  • Built to Order in 12-16 weeks

Rotary Leak Test Machine

Machine capabilities are a 24" wheel diameter with a 14" width.  Clamp plates are rubber-coated to assure an air tight fit seal with wheel and are spaced a minimum 14" apart. The 28” diameter upper platen is flat to accommodate most wheel styles and is interchangeable with a minimum of down time. Operator loads wheel onto clamp assembly.

Machine Details

  • Machine is equipped with two-hand anti-tie down controls, for operator safety.
  • Water tank is stainless steel with ½” polycarbonate plastic window for visual inspection.
  • Water tank will be equipped with two (2) 1.5” NPT connection fittings.
  • Urethane is 90 durometer on platens. 
  • Cycle time is estimated at 35-45 seconds. {PLC is AB}
  • No Hydraulic Power Pack Required. Power requirement is 110 Volt. 
  • Air requirement 75psi with ½” air supply line to machine
  • Machine Dimensions are: 50” Wide x 170” Tall x 57” Deep. Machine weight is 3,600 Lbs.
  • Made in the USA
  • Built to Order in 12-16 weeks

Sequence of operation:

1.

Operator activates two-hand control and pneumatically clamps wheel.

2.

Operator presses start button, which pressurizes wheel to 65 pounds. Machine hydraulically intensifies clamp and raises water tank simultaneously. (Fill pressure is adjustable up to a maximum of 75psi.)

3.

Wheel then rotates 360 degrees for visual leak testing by operator. Controls allow stop and reversing of motor during visual test cycle.

4.

Upon completion of visual leak test cycle water bath tank lowers.

5.

Wheel then de-pressurizes and clamp assembly then releases wheel.

For Additional Information: 

Please contact Gus Del Rivero for additional information:

Cell: 562-264-9565   |  Email: gus@globalcommercialtrading.com


Please contact Gus Del Rivero for additional information:


Cell:

562-264-9565  


 Email: gus@globalcommercialtrading.com


Sequence of operation:

1.

Operator activates two-hand control and pneumatically clamps wheel.

2.

Operator presses start button, which pressurizes wheel to 65 pounds. Machine hydraulically intensifies clamp and raises water tank simultaneously. (Fill pressure is adjustable up to a maximum of 75psi.)

3.

Wheel then rotates 360 degrees for visual leak testing by operator. Controls allow stop and reversing of motor during visual test cycle.

4.

Upon completion of visual leak test cycle water bath tank lowers.

5.

Wheel then de-pressurizes and clamp assembly then releases wheel.

For Additional Information: 

Please contact Gus Del Rivero for additional information:

Cell: 562-264-9565   |  Email: gus@globalcommercialtrading.com


Please contact Gus Del Rivero for additional information:


Cell:

562-264-9565  


 Email: gus@globalcommercialtrading.com


A Provider You Can Trust

STAY IN TOUCH

Don't miss out on important industry information and new product offerings. 

Sign up for our mailing list.